New toy on the desk: Galaxy tab A6

At least I gave up and decided for buying myself a tablet. I've always been more favorable towards netbooks instead of tablets mostly because real computers, even under-powered, better suits the way I use them: mostly writing documents and programming. I didn't entirely changed my mind but I have to reckon a tablet can have many uses where it perform superbly like browsing the Internet or keeping in contact with e-mail or the many social media applications. Last but not least I needed a modern device for studying and testing Android development, so here I am ...

Setting-up the Raspberry PI 3 as a home server

It has been some time since last time I wrote, unfortunately my job stole most of my limited free time keeping me from experimenting and so posting about it. At last I managed to collect enough free time to complete Raspberry PI 3 installation and replace the older model I was using as home server.

Just like before? Not exactly

When I started configuring and installing the Raspberry PI 3 I was hoping it would have been a simple repetition of operation I already performed on the older Raspberry. Most of it has been that way but in some cases I experienced some relevant difference.

Configuring a static IP address

I've been configuring static IP address on Linux since I installed my first Pentium III based Linux, so I really didn't expect any problem here. Once I configured “/etc/networking/interfaces file” I instead noticed the Raspberry was visible on the network with two different addresses. After some searching on the Internet I discovered it's because of a different way DACP client works on latest Raspbian release. The problem can be solved in two ways: first is configuring DHCP client in order to let it set a static address on network interface alternatively it's possible disable DHCP client for one or more network interface. I chose the latter, at the end, since the Raspberry is going to be a DHCP server so there is no deal in keeping DHCP client active. I disabled DHCP client from assigning address to both wired and wireless network interface by adding the following line to “/etc/dhcpcd.conf” configuration file.

denyinterfaces wlan0 eth0

DHCP server and wireless access point

Like I did on my first Raspberry server I configured the new one to work as DHCP server and a wireless access point. It seem there are no relevant changes since first time I did it, I simply had to follow my own instructions.

Installing applications

Installing apt-ger based applications like LAMP sever and MiniDLNA server has been a quite easy task, while to install other applications like RPI-Monitor I had to look for the updated download link on the Internet. I also installed the updated version of SFPG picture gallery, it works but picures thumbnails don't show. I'll look for a solution later.

Power supply and cables

Once I had the Raspberry PI 3 installed and configured on my desktop I pit it in place of the old one and … nothing was working. It took me some time of testing and pinging before I noticed the board power led wasn't properly lighted-up. The phone/tablet charger I used to supply the old Raspberry wasn't up to the Raspberry PI 3 power requirement. I replaced the power supply with the one I used for desktop test but it wasn't enough to make the Raspberry PI 3 working, I had to replace micro-USB power cable with a shorter one in order to have it working, I think it's better I'll buy a dedicated Raspberry PI 3 power supply soon.

New toy on the desk: Raspberry PI 3

Just before Christmas I've been to a “traditional” electronics and surplus fair, here in Genoa, and bought myself, among other things, a Raspberry PI 3 (version B) board. My goal is to replace, as home server, the Raspberry PI I bought two years ago in order to take advantage of the more computing power offered by the new board. Additionally the older board will be set free for more “experimental” experiments. As “accessories” to my new Raspberry board I bought a (clear) plastic case, a 16GB micro SD card and en external 2.5'' USB hard disk.

Installation and first tests

I first downloaded latest Raspbian release, the “Lite” version since I'm going to use it as a headless server. Like I did last time I copied the disk image on the 16GB SD card using the “dd” command.

sudo dd if=2016-11-25-raspbian-jessie-lite.img of=/dev/sdd

All worked fine but I had to fix a couple of things. The image I copied at the first tentative didn't boot, I had to remove all memory card partitions using Gparted then repeat the copy process. The disk copied after the second tentative works fine, I don't know if problem was because a failure in the first copy or because of how the card was pre-formatted.

The latest Raspbian release has SSH demon disabled by default to enable it I had just to add an empty “ssh” named file on the memory card root folder.

touch /media/maxx/boot/ssh

Test drive: (Raspberry PI) Pixel on the EEEPC 900

I own a Raspberry PI since two years but I used it as headless server from the very beginning. I have, almost, never seen its window manager apart from some remote desktop experiment. I so learned only recently how latest Raspbian released are shipped with a new lightweight desktop environment: Pixel. More recently I also learned that Pixel has been released for X86 “common” computers I decided to test how it runs on my EEEPC 900 netbook.

First impressions

I downloaded Pixel ISO disk image from here and prepared a bootable USB disk. Raspberry page suggested using Etcher to prepare the boot disk but UNetbootin did the job as well as usual.

The boot process went smooth and quite fast, and Pixel here is my very first screen-shot of Pixel.

Merry Christmas

A sincere

MERRY CHRISTMAS!

and a

HAPPY NEW YEAR!

To all my readers and visitors